🔒 100% private — runs in your browser, nothing is uploaded

QR Code Parser

Decode a QR code from an image or your camera — text and links, read on your device.

Decoding is the reverse of making a code, and it happens in a fixed order. The image is drawn into the page, its pixels are handed to the jsQR decoder that this site hosts itself, and the decoder hunts for the three finder squares in the corners, samples the grid between them, and repairs damaged modules with the code’s built-in Reed–Solomon error correction before turning the surviving bits back into text. All of that runs in your browser: the picture, and the camera stream if you use it, never leave the device, and there is nothing to sign up for.

Open an image, or start the camera, to decode a QR code.

Your image is decoded in this browser only — it is never uploaded. If the camera will not start, the usual cause is a denied permission: check the browser’s site settings for camera access, allow it, and try again. Making a QR code instead? That is the QR Code Generator’s job — generation is over there, decoding is over here.

Quick answers

How do I decode a QR code from an image?

Open the image in a parser: it draws the picture locally, locates the code’s finder patterns, samples the grid with error correction, and returns the text or link the code holds — for example https://example.com comes back as a URL you can copy or open.

Here the decoding uses the self-hosted jsQR library in your browser, so the image is never uploaded. If several codes share one picture, only the most prominent one is returned.

Why can a QR code still scan when part of it is damaged?

QR codes carry Reed–Solomon error correction, so a decoder can rebuild missing or misread modules up to the level chosen when the code was made — commonly around 15–30% of the code area.

Past that level the damage wins: heavy blur, glare or a large obstruction leaves too little to reconstruct, and an honest parser reports that no code was recognised instead of guessing.

How to use

  1. Open an image that contains a QR code — a screenshot, a photo or a saved picture — or press Use camera and allow camera access.
  2. Wait a moment while the code is located and read; with the camera, hold the code steady until the result appears.
  3. Read the decoded content, check its type (link, Wi-Fi, contact card or plain text), and copy it with the Copy button.
  4. If the content is a link, use Open link to visit it — check the address looks right first, exactly as you would with any code handed to you.

About this tool

The limits are physical, not artificial. A blurred, tiny, low-contrast or glare-covered code may carry too little information to sample; a code with a logo, a tear or a thumb over more than roughly a third of its area can exceed what error correction can rebuild; and when several codes share one image, only the most prominent one — the first clear code the decoder finds — is returned, so crop to one code at a time for the rest. This site divides the work plainly: generation is in the QR Code Generator and the Code 128 Barcode Generator, decoding is here. A parser can only report what a code contains, never whether the sender was trustworthy, so read a decoded link before you open it.

Frequently asked questions

Why does my image say no QR code was recognised?

The common causes are a code that is too small in the frame, blur or camera shake, glare washing out the contrast, or part of the code being covered or cropped off. Move closer so the code fills more of the picture, tap to focus, avoid reflections, and make sure all four corners — including the quiet white border around the code — are in the image, then try again.

Can this read a QR code from my camera live?

Yes. Press Use camera and allow the permission when the browser asks; frames are decoded on the device until a code is found. If you refuse — or refused earlier — live decoding cannot start, and the page says so plainly: allow camera access for this site in the browser settings, or fall back to opening a photo or screenshot of the code, which needs no permission at all.

What kinds of content can a QR code hold, and how does the page label them?

Most hold plain text or a web address. This page classifies each result coarsely as a URL, a Wi-Fi join string (it starts with WIFI:), a contact card (it starts with BEGIN:VCARD), or plain text, and only URL results get an Open link button. A Wi-Fi or contact result is shown as text to copy into the right app rather than acted on automatically.

Is my image or camera feed uploaded anywhere?

No. The file is drawn into this page and decoded locally, and camera frames are processed in the browser and discarded. Nothing is uploaded, stored or put into a link — close the page and the image and its result are gone with it.

📦 Embed this tool on your site

<iframe src="https://verystep.com/embed/qrcode-parser/" title="QR Code Parser" width="100%" height="520" loading="lazy" style="border:0"></iframe>

Free to use. The embed shows a small "Powered by Verystep" link.

First time embedding? Read the step-by-step guide →

More free tools