3D Print Cost Calculator
Price a 3D print properly: filament, electricity and machine wear, with the failed-print allowance shown as an open formula.
The sticker cost of a print is the filament, and filament is only part of the bill. The worked example on this page: a 100 g print from a $25/kg spool is $2.50 of plastic; five hours on a 200 W printer is exactly 1 kWh, worth $0.20 at $0.20 per kWh; machine wear at a modest $0.20 an hour adds $1.00. The direct cost is $3.70 — already half again the filament-only figure most people quote. None of the inputs is exotic: slicers report grams and hours, printer makers state the wattage, and a wear rate can be as simple as the machine’s price divided by the hours you expect from it.
How the failure allowance works, in the open: the direct cost (filament + electricity + machine wear) is divided by the success rate — total = direct cost ÷ (1 − failure rate). At a 10% failure rate that is cost ÷ 0.9, because on average one print in ten has to be made twice. Set it to 0 if you only want the single-print cost. Filament weight should include supports and brims your slicer reports, not just the finished part.
Quick answers
How do I calculate the cost of a 3D print?
Add filament (grams ÷ 1,000 × price per kg), electricity (hours × watts ÷ 1,000 × price per kWh) and machine wear (hours × wear rate). Example: 100 g at $25/kg + 5 h at 200 W and $0.20/kWh + $0.20/h wear = $2.50 + $0.20 + $1.00 = $3.70 per print.
Then divide by the success rate if you want the cost per good print: at a 10% failure rate, $3.70 ÷ 0.9 = $4.11.
How much electricity does a 3D printer use?
A typical desktop printer draws 100–250 W while printing. Five hours at 200 W is 1 kWh — about $0.20 at $0.20 per kWh. Electricity is almost never the deciding cost of a print; filament and failed prints are.
Heated beds dominate the draw on most machines, so enclosed high-temperature printing sits at the top of the range.
How to use
- Read the filament weight from your slicer — the total it will extrude, including supports, brim and purge, not just the finished part’s weight.
- Enter your filament price per kilogram and the print time in hours.
- Add the printer’s power draw in watts and your electricity price; add a per-hour machine wear figure if you want depreciation counted (nozzles, belts, build plates, the machine itself).
- Set the failed-print allowance to your realistic failure rate and read the direct cost and the cost per good print — the formula dividing by the success rate is printed on the page.
About this tool
The failure allowance is the line most cost calculators hide, so this page prints its method in the open: the total is the direct cost divided by the success rate — total = direct cost ÷ (1 − failure rate). At a 10% failure rate the $3.70 print becomes $4.11 per good print, because on average one attempt in ten is printed twice. That is the honest basis for pricing prints for others, and a useful prod for your own printing: every point you shave off the failure rate is money. If you only want the single-attempt cost, set the allowance to 0 and the two lines agree.
Frequently asked questions
How is the failure allowance calculated?
Total cost = direct cost ÷ (1 − failure rate). A 10% failure rate divides by 0.9, turning $3.70 into $4.11 per good print. The reasoning: if one print in ten fails after using its full materials and machine time, ten good prints require about eleven attempts’ worth of inputs. The formula is printed on the page itself — no hidden markup.
What should I use for machine wear / depreciation?
A simple honest method: machine price divided by expected service hours, plus a little for wear parts. A $300 printer you expect 1,500 hours from is $0.20 an hour — the default here. If you are costing your own hobby prints and do not care about wear, set it to 0; if you sell prints, leaving it out is undercharging.
Should the filament weight include supports?
Yes. Cost follows what leaves the spool, and supports, brims, rafts and purge lines all leave the spool. Your slicer’s total filament figure already includes them — use that number, not the model-only weight some slicers also display.
What about labour and post-processing?
They are real costs this calculator deliberately does not invent a number for: your time loading, monitoring, removing supports and finishing is worth what you decide it is worth. Add it per print on top of the figure here if you are quoting a price — the page covers materials, energy and machine, and says so.
First time embedding? Read the step-by-step guide →
More free tools
Cost & Profit Margin Calculator
Markup vs margin, side by side — total cost, unit cost, profit, plus the price you need for a target margin.
Pricing & Profit Calculator
Reverse-price from your landed cost: the selling price a target margin needs after price-based fees, and the profit any price really leaves.
Percentage Calculator
Work out percentages, increases and discounts in one click.
Age Calculator
Find your exact age in years, months and days.
BMI Calculator
Check your Body Mass Index in seconds.
Tip Calculator
Split the bill and work out the tip in seconds.