🔒 100% private — runs in your browser, nothing is uploaded

One Rep Max Calculator

Estimate your one-rep max from a set you have actually done — three formulas, plus a percentage table.

Knowing roughly what you could lift for a single all-out rep is genuinely useful, because most training is prescribed as a percentage of it — 75% for volume work, 85% and up for heavy days. Testing a true maximum is a production: spotters, a long warm-up, and a real chance of a missed lift. Estimating it from a set you have already done is the everyday alternative, and that is what the three published formulas on this page do.

Estimates only, worked out in your browser from the weight and reps you type. The three formulas are explained below; the percentage table uses their average. If you train in pounds, pick lb and the kilogram figures appear in brackets (1 lb = 0.45359237 kg).

Share this exact result — the link carries these inputs, nothing is stored.
⚠️ Estimates from submaximal sets are approximations that vary by exercise and by lifter. This page is not medical or coaching advice. Never attempt a true one-rep max alone or without proper supervision and a thorough warm-up.

Quick answers

How do I estimate my one-rep max without testing it?

Lift a weight for a hard set of 2-10 reps and apply a formula: Epley multiplies the weight by (1 + reps/30), Brzycki by 36/(37 − reps), and Lombardi by reps^0.10. Averaging the three is a reasonable estimate.

For example, 100 kg for 10 reps gives 133.33 kg (Epley), 133.33 kg (Brzycki) and 125.89 kg (Lombardi), an average of 130.85 kg. Lower-rep sets estimate more reliably; a set of 3 sits much closer to a true single than a set of 10.

What percentage of my one-rep max should I train with?

As a rough guide, sets of about 5 reps sit near 85% of one-rep max, sets of 8-10 near 70-75%, and technique or volume work often runs at 60-70%. This page’s table converts those percentages into actual weights from your estimated max.

The percentages come from the estimated average, so they inherit its roughness. If a weight the table calls 80% feels like a maximum, believe the bar rather than the table and adjust.

How accurate is a one-rep max calculator?

Good enough to set training weights, not good enough to settle arguments. Expect the true figure to be within a few percent for low-rep sets on common lifts, and noticeably further off for high-rep sets or less common exercises.

Accuracy depends on the exercise, the lifter and how close the set was to failure. The three formulas on this page disagree with each other by up to about 6% at 10 reps (125.89 kg vs 133.33 kg on a 100 kg set), which is an honest picture of the uncertainty involved.

How to use

  1. Enter the weight of a set you completed with decent form — a hard set, not a warm-up.
  2. Enter how many reps you got with that weight (between 1 and 30).
  3. Read the three estimates and their average, then use the percentage table to pick working weights as a share of the average.
  4. If you log in pounds, switch the unit to lb; the same figures are shown in kilograms in brackets.

About this tool

Each formula takes a slightly different view of how strength fades as reps climb, so each gives a slightly different number. Epley assumes every extra rep adds a thirtieth of the weight again; Brzycki scales the weight by 36/(37 − reps); Lombardi raises the rep count to the power 0.10. For 100 kg lifted 10 times they land at 133.33 kg, 133.33 kg and 125.89 kg, and the page also shows the average, 130.85 kg, since no single formula deserves the last word. The gaps widen as reps rise, which is why low-rep sets estimate better than high-rep ones.

Keep the limits in view. These are estimates built on averages across many lifters; your own result shifts with the exercise (a formula tuned on bench press behaves differently on deadlifts), with your training history, and with how honest the set was. Treat the output as a sensible starting point for choosing training weights, not as a proven maximum — and if a set took more than about 10 reps, treat it as a rough guide at best. This calculator refuses sets above 30 reps for exactly that reason: past that point the formulas are extrapolating so far from a single rep that the number stops meaning much.

Frequently asked questions

What is my estimated one-rep max for 100 kg × 10 reps?

About 130.85 kg on average. The Epley formula gives 133.33 kg, Brzycki gives 133.33 kg, and Lombardi gives 125.89 kg; the calculator shows all three and their average rather than pretending one of them is exact.

What about 60 kg × 5 reps?

About 69.33 kg on average: Epley gives 70.00 kg, Brzycki gives 67.50 kg and Lombardi gives 70.48 kg. Notice how much closer the three sit than they do at 10 reps — shorter sets leave less room for the formulas to disagree.

Why do the three formulas disagree?

They model fatigue differently. Epley adds a fixed share of the weight per rep, Brzycki uses a ratio that steepens as reps approach 37, and Lombardi grows slowly by a power curve. Real lifters fatigue at different rates depending on the lift and their training, so the formulas spread out — averaging them is a pragmatic middle, not a guarantee.

Why is a set of 10 a rougher estimate than a set of 3?

A 3-rep set is close to a single in effort, so there is little to extrapolate. A 10-rep set is much further away: endurance, technique breakdown and pacing all creep in, and small differences in how tired you were swing the estimate by several kilos. The same logic is why this page stops at 30 reps.

Are the weight and reps I type stored?

No. The maths runs in your browser, and the figures are also safe to share: the Copy share link button at the top of the page carries them in the link itself, nowhere else.

📦 Embed this tool on your site

<iframe src="https://verystep.com/embed/one-rep-max-calculator/" title="One Rep Max Calculator" width="100%" height="520" loading="lazy" style="border:0"></iframe>

Free to use. The embed shows a small "Powered by Verystep" link.

First time embedding? Read the step-by-step guide →

More free tools