Verystep Guides Verystep Guides
How to Work Out What an Appliance Costs to Run
An appliance cost is three numbers multiplied together β watts, hours, and the price of a kilowatt-hour. Get those three right and the daily, monthly and yearly figures take care of themselves.

The calculator asks for three inputs: the appliance's watts, the hours per day it runs, and your electricity price per kWh. It returns the energy used in kWh and the cost per day, per month and per year. The math inside is short β watts divided by 1,000 gives kilowatts, kilowatts times hours gives kilowatt-hours, and kilowatt-hours times price gives cost. The errors that wreck the answer rarely come from that math. They come from the inputs: a peak wattage copied off a box, 24 hours typed in for a cycling fridge, or a unit price guessed instead of read off a bill.
Three inputs, and where each one comes from
Watts come from the appliance itself β a rating label, a nameplate near the cord or motor, or the manual. Hours come from your own routine, honestly estimated. Price comes from your bill. Three sources, each with a typical way of going wrong, which is why this guide spends more time on the inputs than on the arithmetic.
The output gives you both halves of the picture. The kWh figures tell you how much energy the appliance uses, which stays the same wherever you live. The cost figures translate that energy at your price, which is why the same heater costs one household more than another. If your tariff changes, the kWh column lets you reprice it at once.
Run the calculator in seven steps
Open the Appliance Running Cost Calculator and work down this list. Have the appliance label and a recent bill in front of you before you start.
- Find the appliance's watts on its rating label, manual, or nameplate, and use the running watts rather than a peak or marketing figure.
- Open the Appliance Running Cost Calculator and enter those watts exactly as printed, without converting them yourself first.
- Enter the hours per day the appliance actually runs at that wattage, using a typical day rather than the longest day you can remember.
- Enter your electricity price per kWh from a recent bill, or divide the bill total by the kWh used if the unit price is not printed clearly.
- Read the daily, monthly, and yearly cost together with the kWh figures, and check that the monthly figure uses a 30-day month.
- If the appliance cycles on and off, such as a fridge or air conditioner, lower the hours to reflect run time instead of leaving it at 24 hours of full power.
- Change one field at a time β watts, hours, or price β and re-read the yearly cost so you can tell which input drives the bill most.
Step two deserves a pause. The tool wants watts, not kilowatts, and it converts itself. Divide by 1,000 before typing and you will understate the cost a thousandfold. Type what the label says.
A worked run: a 1,500W heater, four hours a day
Take a portable heater rated at 1,500W, run for 4 hours a day, at $0.20/kWh β one price for every figure in this example. The conversion: 1,500W is 1.5 kW, and 1.5 kW for 4 hours is 6 kWh/day. Across a 30-day month that is 180 kWh, and across a year it is 2,160 kWh/year. The cost at $0.20/kWh: $1.20/day, $36/month, and $432/year. Check your screen against those six numbers. If the kWh figures match but the costs do not, your price field is wrong.

That yearly figure is the one worth sitting with. A heater that feels cheap at $1.20 a day is a $432 appliance across a year of daily use. Neither number is wrong β they are the same habit read at two scales.
A second example, and the duty cycle trap
Here is a per-use appliance, priced at a different rate β each example keeps one consistent price inside itself. A washer rated at 500W runs 1 hour per load, and you do 20 loads a month. That is 500W, or 0.5 kW, for 20 hours a month, which is 10 kWh/month. At $0.17/kWh for this example, the cost is $1.70 a month. Small, and correctly small β a washer draws far less than a heater's element, and it runs in short bursts.
Now the trap. A fridge is plugged in for 24 hours, but its compressor does not run for 24 hours. It cycles β on to cool, off when the cabinet is cold enough, on again later. An air conditioner does the same once a room reaches the set temperature. Enter the nameplate watts with 24 hours and the tool will price a fridge that never rests, and the yearly cost can come out two or three times too high. For cycling appliances, estimate the share of the day the compressor runs β a third to a half is a common rough range for a fridge β and enter that many hours instead.
Finding watts and price without guessing
For watts, trust the rating label over everything else. It sits on the back or underside of most appliances, on a nameplate near the motor on larger ones, and in the manual's specifications table. Use the running figure printed there. Be wary of packaging and listings, which may headline a peak wattage the appliance touches for a moment, not the draw it sustains. If a label gives amps and volts instead, multiply them for a close wattage β 10 amps at 120 volts is about 1,200W.
For price, open a recent bill. Most bills print a unit rate per kWh. If yours bundles charges so the unit price is hard to spot, divide the bill total by the kWh used that month. That gives an all-in rate β a bit higher than the bare energy rate, because it spreads fixed charges across your usage β but it is honest and fine for comparisons.
Common errors that wreck the answer
Error one is the conversion slip from step two: converting watts to kilowatts yourself, then entering the smaller number in a field that expects watts. Error two is the longest-day habit β pricing a heater at cold-snap hours rather than a typical day. Error three is mixing prices between comparisons, so the cheaper-looking appliance only wins because of its tariff. One price per comparison.
Error four is forgetting what the tool cannot know. It does not know your tariff changes by time of day, and it cannot hear a compressor cycling. Those are your adjustments, in the hours and price fields. Feed it careful inputs and its arithmetic is exact. Feed it a peak wattage, a full day and a guessed price, and it is still exact β exactly wrong.
The Verystep Appliance Running Cost Calculator takes watts, hours per day and your electricity price per kWh, and returns daily, monthly and yearly cost plus the kWh used. Run the heater example from this guide first so you know the output reads right, then swap in the wattage from your own appliance label.
Last verified November 16, 2026 β steps, fields and worked figures checked against the Verystep Appliance Running Cost Calculator and standard appliance cost math.
Frequently asked questions
Where do I find the watts for my appliance?
On the rating label or nameplate β usually on the back, underside or near the cord or motor β or in the manual's specifications table. Use that running figure, not a headline peak figure from packaging or a listing.
Do I need to convert watts to kilowatts before entering them?
No. The watts field expects watts exactly as printed, and the tool divides by 1,000 itself. A 1,500W heater entered as 1,500 returns 6 kWh/day at 4 hours a day. Enter 1.5 instead and every result shrinks a thousandfold.
Why does my fridge's yearly cost look impossibly high?
Because a fridge does not draw full power all day. Its compressor cycles on and off, so pricing the nameplate watts at 24 hours prices a machine that never rests. Estimate the hours the compressor actually runs β often a third to a half of the day β and enter that instead.
My bill does not show a clear price per kWh. What should I enter?
Divide the bill total by the kWh used in that billing period. That gives an all-in rate that spreads fixed charges across your usage, so it runs a bit above the bare energy rate. It is a fair rate for comparing appliances, as long as you use it for all of them.
How does the monthly figure relate to the daily and yearly ones?
The tool builds the monthly figure on a 30-day month and the yearly figure on 365 days. In the heater example, 6 kWh/day becomes 180 kWh in a 30-day month and 2,160 kWh/year, which at $0.20/kWh is $1.20/day, $36/month and $432/year.
More guides

How to Use an Auto Loan Calculator to Compare Two Offers
Two dealers can quote payments that look almost identical and still be selling you loans that cost hundreds of dollars apart. The calculator shows you where the gap hides.

How to Build a Debt Payoff Order: Avalanche vs Snowball, Step by Step
Paying extra money toward debt only works if the extra money has a target. This guide builds that target: an ordered list, made two different ways, so you can see exactly where each spare dollar goes.

How to Project Compound Growth (and Read the CAGR Mode)
This calculator does two jobs in one place: it projects a balance forward at a rate you set, and it works backwards from two balances to the steady rate that links them.